Panel Upgrades
Service upgrades and panel replacement for homes that have outgrown their supply.
Last updated
If you are adding air conditioning, a hot tub, a shop or an EV charger, the panel is usually what has to change first. We upgrade services and replace panels, and coordinate the utility disconnect and the inspection.
Some older panel brands — Federal Pacific and Zinsco in particular — are known fire risks and many insurers will no longer cover a home that still has one. If you have one, replacing it is not optional maintenance.
Panel Upgrades calls in Durango run out of our 178 Bodo Dr, Suite C office. We cover Durango, Bayfield, Ignacio, Hesperus, Mancos, Vallecito and the rest of La Plata County, and the Durango crew is on call 24 hours a day.
How to tell the panel is what is holding the house back
The clearest sign is a breaker that trips when two ordinary things run at once — a microwave and a toaster, a window unit and a vacuum. That is not a faulty breaker doing something wrong. It is a breaker doing exactly its job on a circuit being asked for more than it was built to carry.
The others are easier to spot than people expect. A panel with no empty spaces left, so nothing new can be added without doubling up. Lights across the house dipping when the air handler or a well pump starts. Fuses instead of breakers. A main marked 60 or 100 amps in a house that has since gained central air, an electric range and a dryer. Two wires landed under one breaker screw. A cover warm to the touch, a panel that buzzes, a smell of hot plastic, or rust streaks down the inside of the door.
The last three are worth a call the same day rather than at your convenience. Heat and smell at a panel mean a connection is already failing.
What size service a house actually needs
Service size is settled by a load calculation, not by the age or the square footage of the house. The calculation adds up the general lighting and receptacle load, then the fixed appliances — range, dryer, water heater, air conditioning, well pump, hot tub, EV charger — and applies the demand factors the code allows, because a house never runs everything at once.
100-amp service is still adequate for a good number of homes here, particularly smaller ones heated with gas. What pushes a house to 200 amps is usually a combination rather than a single appliance: refrigerated air added to a house built for a swamp cooler, an electric range alongside an electric dryer, a well pump and pressure system, a shop with a welder or a compressor, or an EV charger.
Where the number comes from matters, because an upgrade sized by guesswork is either money spent for nothing or a panel that is full again in two years.
The panels we install
We specialize in Square D, which is what goes in unless there is a reason to do otherwise, and we work on every other current manufacturer. Where a house already has a panel from one of the makes with a documented safety history, the recommendation is replacement rather than repair: a new breaker in an obsolete enclosure inherits the problem.
Where a particular brand is specified by a builder, an electrical engineer or an insurer, we fit that instead and say so on the quote.
The panel brands an insurer will ask about
Federal Pacific Stab-Lok panels and Zinsco panels, both common in houses built from the late 1950s through the 1970s, have a documented history of breakers that fail to trip on an overload or a short. A breaker that does not trip is not a nuisance — it is the one safety device on that circuit declining to operate while the wiring behind the wall keeps heating up.
Challenger panels from the 1980s draw similar questions. Several insurers now decline to write or renew a policy on a house that still has one of these panels, and a home inspector will flag it during a sale. If an inspector or an insurance agent has told you your panel is a problem, this is usually what they were looking at.
Most of them can be identified from the label inside the door, without opening anything up.
Aluminum branch wiring, and why it comes up during a panel job
Houses wired roughly between 1965 and 1973 — a period covering a great deal of Farmington and the towns around it — were often run with solid aluminum branch circuits, because copper was expensive at the time. Aluminum is a perfectly good conductor. The difficulty is at the terminations: it expands and contracts more than copper as it heats and cools, and over decades that movement can loosen a connection under a screw, which then runs hot.
It comes up during a panel change because the panel is where every one of those connections lands, and a panel change is the one moment when all of them are visible at once. It is also the question an insurer asks straight after the panel brand.
Aluminum service entrance cable — the large conductors running from the meter — is a separate thing and is still standard, installed new today. Being told a house has aluminum wiring does not by itself mean the branch circuits are aluminum.
What a panel upgrade costs
A straightforward replacement — panel swapped in the same place, service staying the size it is, nothing unexpected behind the wall — starts around $2,500.
At the other end, about $15,000 buys a fully specified job: a larger service, whole-home surge protection, grounding and bonding brought properly up to current code, and a lifetime warranty on the work.
What moves a quote between those two is mostly outside the panel itself. Going from 100 amps to 200 or more, whether the meter base, mast or service entrance has to be replaced at the same time, overhead against underground, how much of the grounding and bonding was never right to begin with, whether the panel is moving to a new location, and how many branch circuits need extending to reach it.
We quote the whole job before any of it starts, and that quote covers the permit, the inspection and the utility coordination rather than leaving those to arrive afterwards.
What the day looks like, and how long the power is off
A panel replacement is permitted work with an inspection at the end, and that sets the sequence. The permit is pulled first. The utility is scheduled to pull the meter or cut the service, because the conductors feeding the panel stay live right up to the main breaker and cannot be worked on otherwise.
The old panel comes out, the new one is mounted and the service conductors are landed, then every branch circuit is moved across, identified and labeled. Grounding and bonding are brought up to current code, which on an older home is frequently the part that was never right to begin with — a ground rod that was never driven, or a water-pipe bond lost years ago when a section of copper was replaced with plastic.
We guarantee your power will be restored the same day. It is off for the working part of that day rather than for days, and anything that needs to keep running — a freezer, a medical device, a home office — is worth saying before the work is scheduled rather than on the morning.
The permit, the inspection and the utility are ours to arrange
We pull the permit, book the inspection and coordinate with the power company to drop and reconnect the service. None of it is handed back to the homeowner.
The one exception is where the utility itself requires the customer to commit to buying a piece of their equipment. That is their rule rather than ours, and we say so before the work is scheduled rather than partway through it.
Sub-panels, shops and outbuildings
A sub-panel is often the right answer when the main service has capacity but has run out of physical spaces, or when the new load sits a long way from the house — a shop, a barn, a detached garage, an RV hookup.
It is one feeder out to a second panel that distributes locally, which costs less than a full service upgrade and avoids running individual circuits across a property. A detached building has requirements of its own: a disconnecting means at the building, a grounding electrode there, and the neutral and ground kept separate at the sub-panel — the detail most often got wrong.
Whether a sub-panel is enough or the service itself has to grow comes back to the load calculation.
Surge protection, and why it belongs on a panel job
A whole-house surge protective device installs at the panel and clamps the voltage spikes arriving on the service conductors — from utility switching, from a lightning strike some distance away, or from a large motor on the same transformer starting up.
It is an inexpensive addition while the panel is already open and de-energized, and a far more expensive visit afterwards. It protects what the point-of-use strips behind a television cannot: the air conditioner, the furnace control board, the well pump controller, the range, the garage door opener.
Point-of-use protection still has a place for sensitive electronics. The two work together rather than replacing one another.
What this covers
- 200A service upgrades
- Panel replacement
- Breaker replacement
- Sub-panels
- Federal Pacific and Zinsco replacement
- Surge protection

Towns we cover from Durango
Questions
Panel Upgrades in Durango
How do I know if I need a panel upgrade?
The common signs are breakers that trip when two ordinary appliances run together, a panel with no empty spaces left, lights dimming across the house when a motor starts, fuses rather than breakers, or a 60 or 100-amp main in a house that has since added central air or electric appliances. A warm cover, a buzzing sound or a smell of hot plastic means calling the same day. A load calculation is what settles whether the service itself is undersized or the panel has simply run out of room.
What does a panel upgrade cost?
A straightforward replacement starts around $2,500. A fully specified job — a larger service, whole-home surge protection, grounding and bonding brought up to code, and a lifetime warranty on the work — runs to about $15,000, and most sit between the two. What moves it is the service size, whether the meter base and mast have to be replaced with it, and how much of the grounding was never right to begin with. We quote the whole job, permit and inspection and utility coordination included, before anything starts.
How long does a panel upgrade take, and how long is the power off?
We guarantee your power will be restored the same day. A straightforward residential panel replacement is normally a single working day, with the power off for the working part of it rather than overnight. The utility has to pull the meter or cut the service before work can start, so the schedule depends on their appointment as well as ours. Anything that has to keep running during the outage is worth raising before the day.
Do I need a permit to replace an electrical panel?
Yes. Replacing a panel or changing the size of a service is permitted work and is inspected when it is finished. The inspection is the point of it: the finished work gets looked at by an inspector who does not work for the contractor. Unpermitted panel work routinely causes problems during a sale and when an insurer investigates a claim.
Is 100-amp service still enough?
For plenty of homes here, yes — particularly smaller houses heated with gas. It stops being enough when loads stack up: refrigerated air added to a house built for a swamp cooler, an electric range together with an electric dryer, a well pump, a shop with a welder or compressor, or an EV charger. A load calculation answers it for your house rather than for houses in general.
What is wrong with Federal Pacific and Zinsco panels?
Both have a documented history of breakers that fail to trip on an overload or a short circuit, which leaves the wiring behind the wall with no working protection. Challenger panels raise similar questions. Many insurers will not write or renew a policy on a house that still has one, and a home inspector will flag it during a sale. The brand can usually be read off the label inside the panel door.
Can I add an EV charger without upgrading the panel?
Sometimes. A Level 2 charger typically wants a dedicated 40 to 60-amp circuit, and whether the existing service can carry it depends on what else is in the house. Some homes have the capacity and need only a space in the panel; others need the service increased first. It is the same load calculation that answers the panel question, which is why the two are usually quoted together.
Does a panel upgrade mean rewiring the house?
No — they are separate jobs. A panel upgrade replaces the panel and the service feeding it, and reconnects the existing branch circuits to it. Rewiring replaces the circuits themselves. A panel change does bring the grounding and bonding up to current code, and because every circuit is handled at once, it is the point at which problems in the existing wiring tend to come to light.
Need panel upgrades in Durango?
Most repairs are finished on the first visit. Emergency crews run 24/7 across the Four Corners.
