Wiring & Repairs
Outlets, switches, circuits and troubleshooting for faults you cannot find.
Last updated
Dead outlets, breakers that trip for no obvious reason, switches that get warm — these are the faults that are easy to live with and expensive to ignore.
We troubleshoot and repair, add circuits for new equipment, and bring kitchens, baths, garages and exteriors up to current GFCI and AFCI requirements.
Wiring & Repairs calls in Durango run out of our 178 Bodo Dr, Suite C office. We cover Durango, Bayfield, Ignacio, Hesperus, Mancos, Vallecito and the rest of La Plata County, and the Durango crew is on call 24 hours a day.
Why a breaker trips, and what each kind of trip means
There are three different faults behind almost every trip, and they are not interchangeable. An overload is simply too much current for too long on a healthy circuit — the space heater and the microwave on the same run. A short circuit is a hot conductor touching a neutral or a ground, and it trips instantly and hard. A ground fault is current escaping to earth, often through water or a damaged cable.
Which one it is changes the repair entirely, and the pattern usually tells you. Tripping only when a particular appliance runs points at the appliance or the circuit it is on. Tripping at the same time of day points at something on a timer. Tripping in wet weather points at an exterior device or an underground run.
A breaker that will not reset at all, with everything on the circuit unplugged, is reporting a fault in the wiring itself rather than in anything plugged into it.
GFCI and AFCI: what they do and where they belong
A GFCI watches the current going out against the current coming back, and cuts the circuit in a fraction of a second if the two do not match, because the difference is going somewhere it should not — usually through a person. They belong anywhere water and electricity meet: kitchens, bathrooms, laundries, garages, crawlspaces, exteriors and anything near a sink.
An AFCI looks for the electrical signature of arcing, which is what a damaged cable, a loose terminal or a pinched wire does before it sets fire to something. Current requirements put them on most living-area circuits.
Both are test-button devices and both are worth testing. A GFCI that will not trip on its own test button has failed and is protecting nothing, which is a failure nobody notices because the outlet still works perfectly.
Dead outlets, and the ones that come back on their own
A single dead outlet with the breaker on is usually a tripped GFCI somewhere else on the same circuit — frequently in a garage, a bathroom or outside, behind a storage shelf, and often in a different room from the outlet that stopped working. That is the first thing to look for.
An outlet that works intermittently, or that warms up, is a different and more serious thing. It generally means a loose connection, either at the device or at a back-stabbed terminal further up the circuit. Loose connections arc, arcing makes heat, and heat is what starts the fire. Intermittent is not a milder version of dead.
Scorch marks, a brown stain on the faceplate or a plug that falls out under its own weight all mean the device should be replaced rather than used.
Mobile and manufactured homes
Electrical work inside a mobile or manufactured home takes a license separate from a standard electrical contractor license, and M&R holds it. That covers repairs, panel replacements, service connections and wiring upgrades inside the home as well as the feed and the pedestal outside it.
It is worth asking about before booking anybody for this work, because the license is what decides whether a contractor can work inside the home or only up to it.
Older wiring in Four Corners houses
Cloth-insulated wiring from the 1950s and earlier becomes brittle with age and heat, and tends to crumble at exactly the point it is handled, which is inside boxes. Knob-and-tube, older still, has no ground at all and was never designed to sit under insulation.
Solid aluminum branch circuits, used widely between about 1965 and 1973, are sound as conductors but move more than copper as they heat and cool, which over decades can loosen a connection under a screw. Insurers ask about it, and it is remediated at the terminations rather than by replacing every cable.
Ungrounded two-prong outlets are the most visible sign of the era. There are code-compliant ways to deal with them that do not involve rewiring the house, and the one thing not to do is fit a three-prong outlet with no ground behind it, which looks solved and protects nothing.
Adding circuits for things the house was not built for
A dedicated circuit is what keeps a freezer, a well pump, a shop compressor, a hot tub or a window unit from sharing with the rest of the room. Most nuisance tripping in an older house comes down to modern loads on circuits laid out when a kitchen had a refrigerator and a toaster.
Kitchens, laundries, bathrooms and garages all have their own requirements for how many circuits serve them and what protection those circuits carry. Whether a new circuit can simply be added depends on what is left in the panel, which is the same question a panel upgrade answers.
What this covers
- Outlet and switch repair
- New circuits
- Rewiring
- GFCI and AFCI protection
- Troubleshooting dead circuits
- Aluminum wiring remediation

Towns we cover from Durango
Questions
Wiring & Repairs in Durango
Why does my breaker trip only when I use one appliance?
That usually points at the appliance or at the circuit being asked for more than it can carry. Space heaters, window units, compressors and anything with a motor draw heavily on startup. If the same appliance trips the breaker on a different circuit too, the appliance is the problem; if it only trips on that one, the circuit is.
One outlet is dead but the breaker is on. What now?
Look for a tripped GFCI on the same circuit — commonly in a garage, bathroom or exterior wall, often in a different room and sometimes behind something. Press reset. If there is no GFCI, or it will not reset, the circuit has a fault or a loose connection and needs tracing.
Is aluminum wiring dangerous?
Aluminum is a sound conductor; the risk is at the connections, where decades of expansion and contraction can loosen a terminal, and a loose terminal arcs. It is remediated at the terminations rather than by rewiring the house. Insurers commonly ask about it, and a home inspection will note it.
Can I replace a two-prong outlet with a three-prong one?
Not by itself — a three-prong outlet with no ground behind it looks safe and protects nothing, and anything plugged into it is relying on a ground that is not there. There are compliant ways to handle ungrounded circuits, including GFCI protection with the required labeling, and which applies depends on what is in the wall.
What is the difference between GFCI and AFCI protection?
A GFCI cuts the power when current escapes the circuit, which is what happens when it is passing through a person or water. An AFCI cuts the power when it detects the electrical signature of arcing, which is what damaged or loose wiring does before it starts a fire. They guard against different hazards, and modern requirements call for each in different places.
My outlet feels warm. Is that normal?
No. A warm outlet means resistance where there should be none — usually a loose connection at the device or behind it. Loose connections arc and arcing makes heat. Stop using it and have it looked at rather than waiting for it to fail outright.
Do you work on mobile and manufactured homes?
Yes. M&R holds the New Mexico Manufactured Housing Crossover License (#C10461) specifically for this work — repairs, power connections, panel replacements and wiring upgrades.
Need wiring & repairs in Durango?
Most repairs are finished on the first visit. Emergency crews run 24/7 across the Four Corners.
